Typically you'd use this option to monitor your Internet, but your network is more complex and the other side of your Internet connection is more than the default (2) hops away. You can do this by typing ping hostname in Terminal.įinally, you can choose a custom number of hops to monitor. Many sites block these however, so make sure you test it before hand. 4) Installation Requirements Phillips screwdriver Standard-sized, 19 wide rack with a minimum of 1U height available For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
#PEAKHOUR 4 UBNT USG PRO#
Note that for this to work, the host must allow ICMP (Ping) packets. USG-PRO-4 Quick Start Guide Package Contents UniFi Security Gateway Pro Power Cord Mounting Screws (Qty. If you'd like to monitor a specific site or web site address, choose this option and enter the hostname or IP address to monitor. This option is useful if you have a spotty or weak WiFi connection, and may help you optimize the placement of your access point(s). PeakHour assumes your local network is one hop away, or the next hop. This option monitors your connection to the local network (usually Ethernet or WiFi). you do double-NAT or have more than one router). This is the case for most residential Internet connections but may differ if your network is more complex (e.g. Hop #1: Your router or firewall Hop #2: Your ISP PeakHour assumes the other side of your Internet connection is 2 hops away: This option sets up a monitor for your Internet connection. The following describes the what the analysis means: The Validation screen analyses the configuration and attempts to show a real-time view of bandwidth throughput.
#PEAKHOUR 4 UBNT USG HOW TO#
To add an SNMP device, you can either enter it's name or IP address manually via the Add SNMP Device.button or you can use the Scan for SNMP Devices option to actively search your network.įor detailed instructions on how to add an SNMP device, click here. SNMP devices do not automatically advertise their presence. If you're still having trouble, see our UPnP Troubleshooting guide. If your router does not show up, check your router to ensure UPnP or "Universal Plug and Play" is enabled. PeakHour will automatically show UPnP-enabled routers that are found. Search for Devices in the Configuration Assistant makes it as easy as possible to find compatible devices on your network.
Connection Quality monitors the latency to a hop or specific host on the Internet, allowing you to see the latency between you and that endpoint.If your router is not displayed, try resetting it. Look for your router in the detected devices list. Bandwidth Monitors monitor the network through (upload and download) of a device or interface. In PeakHour, open Preferences and choose + > Bandwidth Monitor.A Target is either a Bandwidth Monitor or a Connection Quality Monitor.Usually the problem comes because default IP of USG is 192.168.1.1 and most ISP routers also use this IP.If you're having trouble, have a look at the Monitoring & Compatibility FAQs.
Normally once this done, adopted, and getting internet over WAN you can change the IP of the USG. Once adopted, plug in the WAN interface of your USG to any port on your ISP router and wait until it get and IP from the DHCP server of your ISP router.344 US MSRP USG-XG-8 (2017, Discontinued) 10 Gbps Gateway, rack-mount (8) 10 Gbps SFP+ ports, (1) gigabit RJ45 Ethernet 4. It will have IP 192.168.1.1 here and you can adopt it to your controller. Gigabit routing is no issue, but firewall and encryption speeds are limited, with slightly higher limits than the USG. First plug in a factory default set USG to your switch on the LAN1 interface.Confgure your ISP router to an IP range different to 192.168.1.1 for example set it up to be 192.168.2.1 and enable DHCP server on it, so it will give the USG a IP like 192.168.2.2 on the USG WAN interface.Configure a network in the controller having 192.168.1.0/24 as IP/subnet (192.168.1.1 is the factory default IP of the USG).I experienced best setup following the next steps: Unifi Security Gateways are quite painful to setup, but once done they work great.
0 kommentar(er)
